Leading 10 common forklift mishaps ， forklift operation ought to take note of these matters ！.

Don't ignore the forklift at the workplace. If the operation is not good, there will be major mishaps in mins, and there are several crashes entailing forklifts.

Instance 1: The forklift freight obstructed the driver's sight, and the individual ahead can not be located, causing a moving crash.
Instance 2: In order to preserve the equilibrium of the forklift when lifting heavy goods, the employees used their body weight as the weight, which virtually created casualties.
Instance 3: The size of the forklift cargo goes beyond the permitted width of the route and hangs on the roadside rack, which nearly triggers an mishap.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift vehicle driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter falls and the chauffeur is squashed when the forklift surrender.
Case 7: The forklift driver did not put on a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift procedure should pay attention to these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no obstacles that prevent the security of driving, beep the horn first and then begin.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge have to be safe prior to starting.
3. When the forklift begins with a load, the motorist should initially confirm that the tons is stable and trusted.
4. The begin has to be slow and constant.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole should be tilted in reverse. .
2. Do not lift the fork too expensive when driving. When getting in and leaving the job website or while driving, be careful that there will be no challenges overhead. When the load is traveling, the fork has to not be raised expensive, which will certainly affect the stability of the forklift. .
3. After dumping, the fork should be reduced to the typical driving placement prior to driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal needs to be issued first. High-speed doglegs are banned. High-speed doglegs will cause the car to shed side security and topple. .
5. When the forklift is downhill, it is purely forbidden to turn off the flame and slide, and it is prohibited to brake instantly while driving with lots unless there are unique circumstances.
6. When the forklift is running, it should follow the web traffic rules in the manufacturing facility and have to maintain a particular safety range from the vehicle in front. .
7. When the forklift is running, the load must be in the lowest position that does not hinder the driving, and the gantry should be properly tilted back. The load will not be elevated other than when piling or packing. .
8. The height of the tons should not block the driver's sight. In unique scenarios, when the item affects the forward vision, drive at a low speed when reversing.
9. It is prohibited to switch on the ramp, nor to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility area is 5 km/h, and it should drive safely at a reduced rate when going into the production workshop area. .
11. When the forklift is raised, raised or driven, it is forbidden for personnel to depend on the fork to hold things and play a balancing role. .
12. If troubles are discovered, they will be fixed and reported in a prompt manner, and they will certainly never ever operate with illnesses or hide them.

packing and unloading.
1. When fork-loading things, the range between both forks ought to be adjusted as required to make the load of both forks balanced and not skewed, and one side of the product ought to protest the rack. .
2. It is restricted to collaborate with a single fork or make use of a fork top or pull. In unique scenarios, safety indication should be established to remind bordering pedestrians. .
3. In the process of loading and dumping items, the forklift has to be braked with the brake. .
4. The rate of the car need to be sluggish and steady. Beware not to roll the wheels on the dunnage, so as not to extend the rolled items and injure people. .
5. When utilizing a fork to fork the goods, the fork should be as deep as possible under Electric Forklift Truck for Warehouse the lots, and it ought to be kept in mind that the fork tip must not touch various other goods or items. The lots ought to be maintained with minimal back tilt of the gantry to ensure that the lots does not slide backwards. The pole can be slanted forward somewhat when the lots is lowered to enable very easy positioning of the load and extraction of the forks. .
6. It is prohibited to fork items at high speed and collide with difficult things with the fork head. .
7. When the forklift is functioning, it is forbidden for people to stand around the fork, so regarding stay clear of the collapse of the goods and hurt people. .
8. Overwhelming is banned, and it is prohibited to utilize forks to lift employees to take part in high-altitude procedures to avoid high-altitude falling accidents. .
9. It is not enabled to utilize the brake inertia to slide, place, round or roll items. .
10. It is not permitted to make use of forks to select, transform pallet dump.

Leaving .
1. It is forbidden to leave the forklift when the things on the fork are in the air. Before leaving the forklift, you must unload the goods or lower the fork frame.
2. Pull the parking brake deal with to dead or depress the parking brake switch.
3. The engine is turned off and the power is cut off. (Except for unique circumstances, such as the driver does not leave the vehicle's line of sight and does not go beyond 1 min).
4. Get rid of the secret. .

Forklift Operation Precautions.
1. Before and after the forklift operation, Electric Forklift Truck for Warehouse the appearance should be examined, and gas, lubing oil and cooling water ought to be added.
2. Examine the safety and security efficiency of starting, running and braking.
3. Check whether the lights and horn signals are full and efficient.
4. During the operation of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the exterior leak ought to also be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must inspect prior to leaving the car;.
2. When you run into somebody in front of you throughout driving, you must send a signal at a distance of 5 m;.
3. The driving rate in the factory does not exceed 5 km/h;.
4. When driving, the nadir of the cargo need to be 0.3 m ~ 0.4 m above the ground;.
5. The turning must not be too sharp to stop the tendency of "free switching";.
6. Running up and down the incline ought to be slow-moving and uniform, and no activating the slope is permitted.
7. Do not drive across the slope. When the gradient is more than 10%, the car needs to be driven backwards when worsening;.
8. When the forklift workers lug the goods and progress, if they run into large or hefty goods and go to the vehicle driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork operation is not permitted.
2. It is not allowed to lift the goods for far away driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and various other dangerous chemicals with forks.
5. It is not enabled to make use of inertia force to get the goods.
6. It is not enabled to make use of braking force to expatriation round or easy-to-roll things.
7. It is not allowed to bring people to deal with the pallet or fork, and it is purely restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Vehicle parking is not permitted under the following conditions.
1. Curves, narrow roadways, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the barrier need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844